Hỗ trợ kỹ thuật

Bảng mã lỗi máy in Canon IP2770 và Hướng dẫn cách sửa

Posted on 13/06/2020 by Admin

Khi máy in Canon IP2770 bị lỗi , máy sẽ báo lỗi đèn cam hoặc cam – xanh nhấp nháy luân phiên theo chu kỳ và hiển thị các code lỗi trên màn hình (báo lỗi 5100 / 5200 / B200 …) .

Tương ứng với mỗi chu kỳ và dạng nhấp nháy là một lỗi khác nhau . Hy vọng tài liêu này sẽ giúp ích được các bạn kỹ thuật trong việc kiểm tra sửa chữa máy in Canon Pixma ip2770 IP2772.

Bảng mã lỗi máy in Canon IP2770 báo đèn cam nhấp nháy theo chu kỳ

Lỗi máy	Error code	Báo đèn (nhấp nháy đèn cam )	Thông báo lỗi trên màn hình	Cách xử lý
No paper in the rear tray.	[1000]	2 times	Paper has run out. Load paper. Press the printer’s RESUME button.	Set the paper in the rear tray, and press the Resume/Cancel button.
Paper jam.	[1300]	3 times	Paper is jammed. Remove the jammed paper. Press the printer’s RESUME button. Printing resumes from the next paper.	Remove the jammed paper, and press the Resume/Cancel button.
Ink cartridge not properly installed.	[1687]	4 times	An ink cartridge is not installed properly. Open the printer’s cover, firmly push down the ink cartridge locking cover, and then make sure the ink cartridge is installed properly. Then close the printer’s cover.	Re-set the ink cartridge properly. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge not installed.	[1401]	5 times	The following ink cartridge cannot be recognized. Color Black Printing cannot be executed because the ink cartridge may not be installed properly or may not be compatible with this printer. Install the appropriate ink cartridge. If you want to cancel printing, click Cancel Printing.	Install the ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge temperature sensor error.	[1403]	5 times	The type of print head is incorrect. Install the print head.	Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Error	Error code	LED (Blinking in orange)	Status Monitor message	Solution
Non-supported ink cartridge installed.	[1485]	5 times	The following ink cartridge cannot be recognized. Color Black Printing cannot be executed because the ink cartridge may not be installed properly or may not be compatible with this printer. Install the appropriate ink cartridge. If you want to cancel printing, click Cancel Printing.	A non-supported ink cartridge is installed. Install the supported ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge in a wrong position.	[1486]	7 times	An ink cartridge is not installed in the correct position. Install the following ink cartridge in the appropriate position. If printing is in progress, cancel printing and install the ink cartridge. Color Black	Install the ink cartridge(s) in the correct position. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Multiple ink cartridges of the same color installed.	[1487]	7 times	More than one ink cartridge of the following type is installed. Color Black Use only one ink cartridge per type at a time.	Replace the wrong ink cartridge(s) with the correct one(s). If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Warning: The ink absorber becomes almost full.	[1700]	8 times	The ink absorber is almost full. Press the printer’s RESUME button to continue printing. The printer will soon require servicing to replace the ink absorber. Contact the support center or the service center. The ink absorber can only be replaced by a qualified technician.	Replace the ink absorber, and reset its counter. (See 2-1, Service Mode.) Pressing the Resume/Cancel button will exit the error, and enable printing without replacing the ink absorber. However, when the ink absorber becomes full, no further printing can be performed unless the applicable ink absorber is replaced.
Error	Error code	LED (Blinking in orange)	Status Monitor message	Solution
The remaining ink amount unknown.	[1686]	13 times	The following ink may have run out. Color Black The function for detecting the remaining ink level will be disabled since the ink level cannot be correctly detected. If you want to continue printing without this function, press the printer’s RESUME button for at least 5 seconds. Canon recommends to use new genuine Canon cartridges in order to obtain optimum qualities. Please be advised that Canon shall not be liable for any malfunction or trouble caused by continuation of printing under the ink out condition.	Replace the applicable ink cartridge with a new one. Printing without replacing the ink cartridge can damage the printer. However, to continue printing without replacing the ink cartridge(s), press the Resume/Cancel button for 5 sec. or longer to disable the function to detect the remaining ink amount. After the operation, it is recorded in the printer EEPROM that the function to detect the remaining ink amount was disabled.
Ink cartridge not recognized (region code error).	[1684]	14 times	The following ink cartridge cannot be recognized. Color Black Printing cannot be executed because the ink cartridge may not be installed properly or may not be compatible with this printer. Install the appropriate ink cartridge. If you want to cancel printing, click Cancel Printing.	A non-supported ink cartridge (whose region code differs from the printer’s region code) is installed. Install the supported ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge hardware error.	[1682]	15 times	The following ink cartridge cannot be recognized. Color Black Printing cannot be executed because the ink cartridge may not be installed properly or may not be compatible with this printer. Install the appropriate ink cartridge. If you want to cancel printing, click Cancel Printing.	Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Error	Error code	LED (Blinking in orange)	Status Monitor message	Solution
No ink (no raw ink).	[1688]	16 times	The following ink has run out. Color Black Replace the ink cartridge and close the cover. If printing is in progress and you want to continue printing, press the printer’s RESUME button for at least 5 seconds with the ink cartridge installed. Then printing can continue under the ink out condition. The function for detecting the remaining ink level will be disabled. Replace the empty ink cartridge immediately after the printing. The resulting print quality is not satisfactory, if printing is continued under the ink out condition.	Replace the empty ink cartridge(s). Printing with an empty ink cartridge can damage the printer. However, to continue printing without replacing the ink cartridge(s), press the Resume/Cancel button for 5 sec. or longer to disable the function to detect the remaining ink amount. After the operation, it is recorded in the printer that the function to detect the remaining ink amount was disabled.

Bảng mã lỗi máy in Canon IP2770 báo đèn cam – xanh nhấp nháy theo chu kỳ

Error	Error code	Đèn nhấp nháy cam – xanh (luân phiên theo chu kỳ )	Nguyên nhân	Giải pháp (kiểm tra hoặc sửa chữa / thay thế các bộ phận có liên quan)
Carriage error	[5100]	2 times	An error occurred in the carriage encoder signal.	1) Foreign material or paper debris that obstructs the carriage movement; remove foreign material. 2) Smearing or scratches on the timing slit film; clean the timing slit film. 3) Part replacement: – Timing slit film – Carriage unit – Logic board
Line feed error	[6000]	3 times	An error occurred in the LF encoder signal.	1) Part replacement: – Timing slit disk film – Logic board
ASF cam sensor error	[5700]	5 times	An error occurred in the ASF cam sensor (during paper feeding from the rear tray).	1) Part replacement: – ASF / PE sensor unit – Drive unit – Logic board
Internal temperature error	[5400]	6 times	The internal temperature is not normal.	1) Part replacement: – Logic board – Ink cartridge
Ink absorber full	Japan: [5B01] Others: [5B00]	7 times	The ink absorber is supposed to be full.	1) Part replacement: – Ink absorber kit 2) Ink absorber counter value in the EEPROM; reset the ink absorber counter.
Print head temperature rise error	[5200]	8 times	The print head temperature exceeded the specified value.	1) Part replacement: – Ink cartridge – Logic board
EEPROM error	[6800] [6801]	9 times	A problem occurred in reading from or writing to the EEPROM.	1) Part replacement: – Logic board
VH monitor error	[B200]	10 times	The print head voltage is not normal.	1) Part replacement: – Ink cartridge – Logic board

Trả lời Hủy